標題: 注塑機機筒螺桿安裝注意問題 [打印本頁] 作者: zsxinlu 時間: 2024-6-5 13:08 標題: 注塑機機筒螺桿安裝注意問題 注塑機螺桿一般情況下可分為加料段、壓縮段、均化段。不同的螺桿三段所占的比值不一樣，螺桿槽深不一樣，螺桿底徑過渡形式不一樣。
螺桿是注塑機的重要部件。它的作用是對塑料進行輸送、壓實、熔化、攪拌和施壓。所有這些都是通過螺桿在機筒內的旋轉來完成的。
需要注意的內容如下：
(1)給螺栓的螺紋和螺桿頭羅紋表面均勻涂上高溫防緊蝕膏，以防日后擰不出來；
(2)螺桿型號確認；
(3)安裝螺桿頭確認止逆環介子前后端面與螺桿貼合端面要吻合；
(4)注意在把螺桿裝入料筒時止逆環要用手扶住輕輕往里推，預防止逆環掛到料筒端面；
(5)注意螺桿頭擰緊方向是逆時針；
(6)螺絲必須是強度級別12.9級的優質螺栓，給螺栓的螺紋表面涂上高溫防緊蝕膏；
(7)前法蘭與料筒螺絲一定要對稱均勻擰緊；
(8)注塑機螺桿料筒冷卻系統要清理干凈，保證通暢。注意正確使用生料帶，纏在工藝螺塞上。
Injection machine machine of of injection injection machine
The injection molding machine screw can generally be divided into feeding section, compression section and homogenization section. The ratio of different screw three sections is different, the screw groove depth is different, and the screw bottom diameter transition form is different.
Screw rod is an important part of the injection molding machine. Its role is to transport, compact, melt, stir, and pressure the plastic. All of this is done by the rotation of the screw in the barrel.
Note that the contents are as follows:
1. Apply the thread and the thread surface of the bolt evenly with high temperature anti-corrosion paste to prevent untwisting out in the future;
2, screw model confirmation;
3. Install the screw head to confirm that the front and rear end of the ring pion should coincide with the end of the screw;
4. Pay attention to put the screw into the material cylinder and push it gently to prevent the reverse ring from hanging to the end surface of the material cylinder;
5. Note that the tightening direction of the screw head is counterclockwise;
6, the screw must be a high quality bolt strength level 12.9 level, to the thread surface of the bolt coated with high temperature anti-corrosion paste;
7, the front flange and the material cylinder screws must be tightened symmetrical and evenly;
8, injection molding machine screw cylinder cooling system should be cleaned up to ensure smooth. Note the correct use of the raw material belt, wrapped around the process screw plug. https://www.zsxinlu.com/作者: MLX-BRIAN 時間: 2024-6-5 13:10
支持一下作者: ylyhqaio 時間: 2024-6-5 13:13
看帖回帖是美德！作者: cyflrzlq 時間: 2024-6-5 13:13
幫你頂下哈！！作者: ufjcppbi 時間: 2024-6-5 13:15
過來看看的作者: sbitesax 時間: 2024-6-5 13:16
路過，支持一下啦
